PRO CNC Rotary Axis

• 4 Jaw self-centering chuck (inside and outside jaws included)
• Length adjustable tailstock (live center included)
• Auto Z and Corner Finding Touch Plate compatibility for setting repeatable work offsets
• Pepperl and Fuchs inductive proximity sensor for automated homing/position tracking
• Low inductance Nema 34 stepper motor
• Premium components (profile linear guide rails for tailstock, planetary gear reduction)
• Rigid, self-contained aluminum frame
• Easy step-by-step assembly and calibration instructions
• Proudly designed and supported in the USA

• 5” (130mm) 4 jaw chuck
• Morse Taper (MT) 2 tailstock with included live center
• Nema 34 stepper motor (N23 system compatible via provided motor adapter cable)[1]
• 10:1 Reduction
• Stall torque:
• 24 ft-lbs with Plug and Play NEMA 34 CNC Control System
• 20 ft-lbs with Plug and Play NEMA 23 CNC Control System
• Maximum RPM: 100
• Backlash: 3 arcmin
• Sensor Cable Length: 20'

• Aluminum frame, cut to length, drilled, counterbored, and tapped for easy assembly
• Profile Linear Guide Rails and Bearings
• 4 Jaw chuck and reducer assembly
• Adjustable tailstock
• All required fasteners and gussets for mounting to your machine (see Product Options below)
• Pepperl and Fuchs inductive homing sensor and sensor cable

The Rotary Axis Kit is designed to be highly versatile and accommodate many different workpiece sizes, while maintaining traditional routing work areas.

It can be mounted to an existing machine parallel with the X or Y axis, or can be recessed into the machine frame to maximize workpiece diameter. Mounting parallel to the Y axis (perpendicular to the machine gantry) maximizes workpiece length, while mounting parallel to the X axis preserves greater traditional routing work area. Recessed mounting can only be achieved parallel to the X axis of the machine.

PRO Series CNC machine mounting options:[2]

• Table top, parallel or X or Y axis
• Recessed, parallel to X axis

PRO CNC Rotary Axis, table top mountedPRO4848 machine kit, 49" (1250mm) PRO CNC Rotary Axis, spoilboard, 2.2kW Spindle, NEMA 34 Motors

PRO CNC Rotary Axis, recessed mountedPRO4848 machine kit, 49" (1250mm) PRO CNC Rotary Axis, spoilboard, 2.2kW Spindle, NEMA 34 Motors

Benchtop PRO and Benchtop Standard mounting options:

• Table top, parallel to Y axis

PRO CNC Rotary Axis, table top mountedBTP2424 machine kit, 39" (1000mm) PRO CNC Rotary Axis, 2.2kW Spindle, NEMA 23 Motors

• Maximum swing over bed: 8" (when mounted directly to aluminum machine frame)
• Maximum swing over bed recessed: 12"

To determine the optimal rotary axis length for a specific application, start with the workpiece dimensions.

• Diameter 8" - 12": PRO Series machines only, recessed mounting required. See chart below for recommended rotary axis length.
• Diameter less than 8": Mounted parallel to X or Y axis on PRO Series machines, or parallel to Y axis on Benchtop machines. To achieve the maximum workpiece diameter of 8" with table top mounting, rotary frame must be installed directly to the machine frame (no spoil board underneath rotary axis). See chart below for recommended rotary axis length.

To gain complete access to the full Y travel of a machine, the rotary axis length must exceed the length of the machine frame (overall footprint will be affected). The chart below shows the required rotary axis length to maintain access to the full Y travel of the machine.

Mounting kits are available for both recessed and table top mounting:

• Recessed Mounting Kit includes:
  • (2) Undermount bracket with jack screws for easy alignment of rotary frame
  • (2) Mid-support bracket
  • All fasteners required for recessed mounting
• Table Top Mounting Kit includes:
  • (4) Gusseted corner bracket for mounting to machine frame or spoil board
  • (1) Aluminum joining bar and bracket for fastening headstock to machine frame
  • All fasteners required for table top mounting

Electronics are available for both Plug & Play and DIY control systems:

• Plug and Play control system option includes:
  • (1) NEMA 34 960 oz-in stepper motor
  • (1) 20'High Current CNC Motor Cable
• DIY control system option includes:
  • (1) NEMA 34 960 oz-in stepper motor
  • (1) 20'High Current CNC Motor Cable
  • (1) 7A Bulkhead Enclosure Connector

1. The PRO CNC Rotary Axis uses a NEMA 34 960 oz-in stepper motor. A motor adapter cable will be provided to allow compatibility with NEMA 23 control systems. If your control system does not contain a 5th motor driver, please Contact Us for upgrade options. If you are purchasing one of our Plug and Play CNC Control Systems, select the "5th drive upgrade" option.
2. When ordering a new PRO Series CNC Machine it is recommended to budget 2' of Y travel or 1' of X travel, in addition to your desired traditional routing work area for a permanently installed rotary axis. For example:
   • 4' x 4' traditional work area with rotary axis mounted parallel to the X axis, a 4' x 6' machine is required
   • 4' x 4' traditional work area with rotary axis mounted parallel to the Y axis, a 5' x 4' machine is required

• PRO CNC Rotary Axis Assembly and Calibration Instructions provide a full step-by-step guide to assemble and calibration your rotary axis.
• PRO CNC Rotary Axis Footprints